DOI:

https://doi.org/10.14483/22487638.17148

Publicado:

2022-07-01

Número:

Vol. 26 Núm. 73 (2022): Julio - Septiembre

Sección:

Investigación

Magnetic Barkhausen Noise Measurements on Rocks

Mediciones del Ruido Magnético Barkhausen en rocas

Autores/as

Palabras clave:

rocks, magnetization, Magnetic Barkhausen Noise, non-destructive test (en).

Palabras clave:

rocas, magnetización, Ruido Magnético de Barkhausen, ensayo no destructivo (es).

Biografía del autor/a

Miriam Rocío Neyra Astudillo, Universidad Tecnológica Nacional, Campana, Argentina

Licenciado en Física, Departamento de Ciencias Naturales y Matemáticas, Universidad Federico Villarreal, Lima, Perú. Doctorado en Ciencia y Tecnología con énfasis en Materiales, Informática Sábato, Universidad de San Martín, Argentina. Profesor de la Facultad Regional Delta, Universidad Tecnológica Nacional, Campana, Argentina. Proyecto del Centro Internacional de Estudios de la Tierra (ICES). Centro Atómico Constituyentes, Comisión Nacional de Energía Atómica (CNEA), Buenos Aires, Argentina.

María Isabel López-Pumarega, Universidad de Buenos Aires, Argentina

Licenciado en Ciencias Físicas, Departamento de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Argentina. Doctor en Física, Departamento de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Argentina. Departamento ICES, Comisión Nacional de Energía Atómica (CNEA), Buenos Aires, Argentina.

Silvana Evangelina-Geuna, Universidad de Buenos Aires

Licenciado en Ciencias Geológicas (Universidad de Buenos Aires). Doctor en Ciencias Geológicas (Universidad Nacional de Córdoba). Especialista en Paleomagnetismo de Rocas. Profesor asociado (Geodinámica Interna) de la Universidad de Buenos Aires. Rosario de Lerma, Argentina.

Martin Gómez, Comisión Nacional de Energía Atómica (CNEA)

Licenciado en Ciencias Físicas, Universidad de Buenos Aires. Magíster en Ciencia y Tecnología de Materiales y Doctorado en Ciencia y Tecnología con énfasis en Materiales, Informática Sábato, Universidad de San Martín, Argentina. Profesor asociado, Facultad Regional Delta, Universidad Tecnológica Nacional, Campana, Argentina. Director científico del Centro Internacional de Estudios de la Tierra (ICES). Jefe de departamento ICES, Centro Atómico Constituyentes, Comisión Nacional de Energía Atómica (CNEA), Buenos Aires, Argentina.

Referencias

Butler, R. F. (1992). Paleomagnetism: From magnetic domains to geologic terranes. Blackwell Scientific Publications.

Chaparro, A. E., Gargiulo, J. D., Irurzun, M. A., Chaparro, M. A. E., Lecomte, K. L., Böhnel, H. N., Córdoba, F. E., Vignoni, P. A., Manograsso, C. N. T., Lirio, J. M., Nowaczyk, N. R., & Sinito, A. M. (2014). El uso de parámetros magnéticos en estudios paleolimnológicos en Antártida. Latin American Journal of Sedimentology and Basin Analysis, 21(2), 77-96. http://www.redalyc.org/articulo.oa?id=381741102002

Clark, D. A., & Emerson, D. W. (1991). Notes on rock magnetization characteristics in applied geophysical studies. Exploration Geophysics, 22, 547-555. https://doi.org/10.1071/EG991547 DOI: https://doi.org/10.1071/EG991547

Dunlop, D. J., & Özdemir, Ö. (1997). Rock magnetism: Fundamentals and frontiers. Cambridge University Press. https://doi.org/10.1017/CBO9780511612794 DOI: https://doi.org/10.1017/CBO9780511612794

Ferrari, G. C., & Gómez, M. P. (2020). Caracterización de etapas de perforado en probetas multicapas mediante la emisión acústica generada durante la perforación. Tecnura, 24(63), 26-39. https://doi.org/10.14483/22487638.16193 DOI: https://doi.org/10.14483/22487638.16193

Filipussi, D. A., Muszkats, J. P., Sassano, M. P., Zitto, M. E., & Piotrkowski, R. (2019). Fractura de roca andesita y análisis espectral de señales de emisión acústica. Tecnura, 23(61), 45-56. https://doi.org/10.14483/22487638.15361 DOI: https://doi.org/10.14483/22487638.15361

Hoyos-Palacio, L. M., Espinel-Blanco, E., & Quintero-Martínez, Y. (2015). Caracterización fisicoquímica de cuarzo en el municipio de La Playa de Belén, departamento de Norte de Santander. Tecnura, 19(45), 41-52. https://doi.org/10.14483/udistrital.jour.tecnura.2015.3.a03 DOI: https://doi.org/10.14483/udistrital.jour.tecnura.2015.3.a03

Ivanchenko, V. S., Glukhikh I. I., Strokina, L. G., & Kheinson A. P. (2012). Magnetoacoustic emission of magnetites. Russian Geology and Geophysics, 53(2), 214-220. https://doi.org/10.1016/j.rgg.2011.12.018 DOI: https://doi.org/10.1016/j.rgg.2011.12.018

Jiles, D. (1991). Introduction to magnetism and magnetic materials. Chapman and Hall. https://doi.org/10.1007/978-1-4615-3868-4 DOI: https://doi.org/10.1007/978-1-4615-3868-4

Neyra-Astudillo, M. R. (2017). Caracterización de materiales con técnicas de ruido magnético Barkhausen y emisión magneto acústica [Doctoral thesis, Universidad Nacional de General San Martín]. https://www.cnea.gob.ar/nuclea/handle/10665/1572

Neyra-Astudillo, M. R., Núñez, N., López-Pumarega, M. I. Ruzzante, J., & Padovese-Rodríguez (2018). Ruido magnético Barkhausen para el estudio de la anisotropía magnética en aceros inoxidables. Revista Materia, 23(2), e12118. https://doi.org/10.1590/s1517-707620180002.0452 DOI: https://doi.org/10.1590/s1517-707620180002.0452

Stacey, F. D., & Banerjee, S. K. (1974). The physical principles of rock magnetism. Elsevier.

Stefanita, C. G. (2008). From bulk to nano: The many sides of magnetism. Springer. https://doi.org/10.1007/978-3-540-70548-2 DOI: https://doi.org/10.1007/978-3-540-70548-2

Valencio, D. A. (1980). El magnetismo de las rocas: su aplicación geológica, la deriva continental, la tectónica de placas y otros problemas geofísicos y geológicos. EUDEBA.

Cómo citar

APA

Neyra Astudillo, M. R., López-Pumarega, M. I., Evangelina-Geuna, S. ., y Gómez, M. . (2022). Magnetic Barkhausen Noise Measurements on Rocks. Tecnura, 26(73), 18–29. https://doi.org/10.14483/22487638.17148

ACM

[1]
Neyra Astudillo, M.R. et al. 2022. Magnetic Barkhausen Noise Measurements on Rocks. Tecnura. 26, 73 (jul. 2022), 18–29. DOI:https://doi.org/10.14483/22487638.17148.

ACS

(1)
Neyra Astudillo, M. R.; López-Pumarega, M. I.; Evangelina-Geuna, S. .; Gómez, M. . Magnetic Barkhausen Noise Measurements on Rocks. Tecnura 2022, 26, 18-29.

ABNT

NEYRA ASTUDILLO, Miriam Rocío; LÓPEZ-PUMAREGA, María Isabel; EVANGELINA-GEUNA, Silvana; GÓMEZ, Martin. Magnetic Barkhausen Noise Measurements on Rocks. Tecnura, [S. l.], v. 26, n. 73, p. 18–29, 2022. DOI: 10.14483/22487638.17148. Disponível em: https://revistas.udistrital.edu.co/index.php/Tecnura/article/view/17148. Acesso em: 28 mar. 2024.

Chicago

Neyra Astudillo, Miriam Rocío, María Isabel López-Pumarega, Silvana Evangelina-Geuna, y Martin Gómez. 2022. «Magnetic Barkhausen Noise Measurements on Rocks». Tecnura 26 (73):18-29. https://doi.org/10.14483/22487638.17148.

Harvard

Neyra Astudillo, M. R. (2022) «Magnetic Barkhausen Noise Measurements on Rocks», Tecnura, 26(73), pp. 18–29. doi: 10.14483/22487638.17148.

IEEE

[1]
M. R. Neyra Astudillo, M. I. López-Pumarega, S. . Evangelina-Geuna, y M. . Gómez, «Magnetic Barkhausen Noise Measurements on Rocks», Tecnura, vol. 26, n.º 73, pp. 18–29, jul. 2022.

MLA

Neyra Astudillo, Miriam Rocío, et al. «Magnetic Barkhausen Noise Measurements on Rocks». Tecnura, vol. 26, n.º 73, julio de 2022, pp. 18-29, doi:10.14483/22487638.17148.

Turabian

Neyra Astudillo, Miriam Rocío, María Isabel López-Pumarega, Silvana Evangelina-Geuna, y Martin Gómez. «Magnetic Barkhausen Noise Measurements on Rocks». Tecnura 26, no. 73 (julio 1, 2022): 18–29. Accedido marzo 28, 2024. https://revistas.udistrital.edu.co/index.php/Tecnura/article/view/17148.

Vancouver

1.
Neyra Astudillo MR, López-Pumarega MI, Evangelina-Geuna S, Gómez M. Magnetic Barkhausen Noise Measurements on Rocks. Tecnura [Internet]. 1 de julio de 2022 [citado 28 de marzo de 2024];26(73):18-29. Disponible en: https://revistas.udistrital.edu.co/index.php/Tecnura/article/view/17148

Descargar cita

Visitas

63

Dimensions


PlumX


Descargas

Los datos de descargas todavía no están disponibles.

Recibido: 26 de octubre de 2021; Aceptado: 20 de abril de 2022

Abstract

Context:

The magnetic properties of rocks may reflect the modal abundance, composition, and microstructure of the magnetic grains contained within them, usually in a very small proportion. Magnetic Barkhausen Noise (MBN) is a non-destructive technique applied to magnetic materials, and it is very sensitive to microstructure and residual stresses. In this work, measurements of MBN in samples of rocks extracted from nature and containing varying proportions of magnetite were studied and analyzed.

Method:

Measurements were taken by magnetically exciting the cylindrical samples, using a magnetic yoke and measuring the induced field inside the rock as a consequence of the excitation. For the detection, a sensor coil placed on the excited surface on one of the flat faces of each cylinder was used. The signals obtained from the MBN were digitized, and a digital 5-200 kHz Butterworth filter was applied, calculating the root mean square (RMS) values.

Results:

The linear fit of the MBN RMS values with the increasing percentage of ferromagnetic minerals showed an increasing trend with a moderate correlation. A correlation between coercive force and the MBN RMS values was observed only for samples with abundant magnetite (> 25 vol%).

Conclusions

: An increasing variation of the RMS values of the MBN signals was observed in relation with coercive force for abundant magnetite samples. This may be related to the geological processes involved in magnetite genesis.

Keywords:

rocks, magnetization, Magnetic Barkhausen Noise, non-destructive test.

Resumen

Contexto:

Las propiedades magnéticas de las rocas pueden reflejar la abundancia modal, la composición y la microestructura de los granos magnéticos que estas contienen, usualmente en muy pequeña proporción. El ruido magnético Barkhausen (RMB) es una técnica no destructiva que se aplica en materiales magnéticos y es muy sensible a la microestructura y a las tensiones residuales. En este trabajo se realizan mediciones para estudiar el RMB en muestras de rocas extraídas de la naturaleza que contienen proporciones variables de magnetita.

Método:

Se realizaron mediciones excitando magnéticamente cada una de las muestras cilíndricas mediante un yugo magnético y midiendo el campo inducido en la roca como consecuencia de la excitación. Para la detección se utilizó una bobina sensora colocada sobre la superficie excitada en una de las caras planas de cada cilindro. Se digitalizaron las señales obtenidas de RMB y se les aplicó un filtro digital Butterworth de 5-200 kHz, calculándose el valor cuadrático medio (RMS).

Resultados:

El ajuste lineal de los valores del RMS de RMB con el porcentaje progresivo de minerales ferromagnéticos mostró una tendencia creciente con una correlación moderada. Se observó una correlación entre la fuerza coercitiva y los valores RMS del RMB solo para muestras con abundante magnetita (>25 vol%).

Conclusiones:

Se observó una variación creciente de los valores RMS de las señales de RMB en relación con la fuerza coercitiva para muestras con magnetita abundante. Esto puede estar relacionado con los procesos geológicos involucrados en la génesis de la magnetita.

Palabras clave:

rocas, magnetización, Ruido Magnético de Barkhausen, ensayo no destructivo.

INTRODUCTION

Rocks and minerals, as natural materials, show a wide degree of variation in their physical properties, and measuring some of these properties often serves as a way for rapid and/or precise characterization (Hoyos-Palacio et al., 2015; Filipussi et al., 2019; Ferrari & Gómez 2019).

Rocks can record some of the characteristics of the existing magnetic field at the time of their formation. An important field of geology, paleomagnetism, aims to determine the natural remanent magnetization (NRM) of rocks and interpret it in terms of significant geological events (Butler, 1992; Dunlop & Özdemir, 1997; Valencio, 1980).

Rock magnetism is a field that studies the behavior and magnetic properties of different types of rocks and minerals found in nature. The magnetic characterization of a sample requires measuring various parameters such as magnetic susceptibility, magnetic hysteresis cycles, isothermal/anhysteretic remanence acquisition curves, among others. All these parameters provide essential information to identify the various ferromagnetic minerals present in a sample and their magnetic state (superparamagnetic, single-domain, pseudo-single domain, multidomain), which mainly depends on the size and shape of the grains or crystals (Dunlop & Özdemir, 1997; Ivanchenko et al., 2012).

Rock magnetic studies are usually carried out in addition to any paleomagnetic study, with the purpose of determining what ferromagnetic minerals are carrying the NRM, which can have important implications regarding its origin, stability, and history of acquisition.

In addition, knowing the microphysics of minerals constitutes an interesting field of research. It is also a fundamental tool for environmental or paleoenvironmental magnetism, which attempts to characterize the magnetic phases present in recent or ancient sediments and their variation, both spatial and temporal. Moreover, the connection between environmental or paleoenvironmental parameters and the presence and state of one or more ferromagnetic minerals allows extracting important information (Chaparro-Marcos et al., 2014).

Magnetism in rocks is carried by a few minerals, the most important of which are iron and titanium oxides, such as magnetite and hematite (Stacey & Banerjee, 1974; Dunlop & Özdemir, 1997).

Destructive and non-destructive magnetic measurements are taken in the different rock magnetic studies. Magnetic Barkhausen Noise (MBN) is a non-destructive testing technique that is widely used for the microstructural characterization of magnetic materials. This technique is mainly based on the irreversible movements of the walls of the magnetic domains that must overcome pinning points such as grain edges, dislocations, impurities, etc. These imperfections impede the movement of the domain walls until an increase in the applied magnetic field provides the necessary energy to free the walls from these obstacles. These pinning points produce a sudden jump in magnetization, which causes a flux change called MBN (Jiles, 1991; Stefanita, 2008; Neyra-Astudillo, 2017; Neyra-Astudillo et al., 2018).

In this work, the MBN method is attempted as an alternative technique to study the magnetic characteristics of rock samples that contain different variable proportions of ferromagnetic minerals such as magnetite (Fe3O4). This work evaluates the feasibility of applying the MBN method in the study of magnetic rocks, as there are no references to it in the literature.

METHODOLOGY

Measurements were carried out on 11 cylindrical samples containing different percentages of magnetite. The MBN was measured on the two circular flat faces. The magnetic yoke was fed with a variable current used to generate the excitation field. The variation of the RMS value of the MBN signals was observed in relation to the known magnetic properties of the studied rocks.

Materials

Magnetite (Fe3O4) usually appears in common rocks of the earth's crust as an accessory mineral, that is, in abundances that rarely reach a few percentage points. For this work, samples of ore deposits characterized by a high volume percentage of magnetite were studied, which varied from massive (>50 vol%) to disseminated ore (with concentrations around 5 vol%), belonging to IOCG, BIF, porphyry, and skarns deposits (Table 2). They were cut as cylinders with 23 mm diameter and 20 mm height. The samples were previously demagnetized by applying linearly decreasing alternating magnetic fields (AF). The demagnetization of the NRM was completed with fields of low intensity (about 20-30 mT), which indicates that, in all cases, the magnetite is predominantly in a multidomain state. Table 1 indicates the median destructive field of NRM obtained from AF demagnetization, a measure of the coercive force. Other properties of the specimens such as volume, density, and magnetic susceptibility are also included, which were determined at the Paleomagnetism Laboratory of IGEBA. For illustrative purposes, a column is also included with the approximate estimation of the volume percentage of magnetite, calculated from the value of magnetic susceptibility using the relations of Clark and Emerson (1991), and assuming that magnetite is the only ferromagnetic mineral in the samples. Table 2 indicates the origin of each of the samples along with their geological characterization.

Table 1: Rock magnetic and petrophysical characterization of each sample

Code Volume (cm3) Density (g/cm3) (1) Bulk susceptibility (SI) (2) Median destructive field (mT) (3) Approximate magnetite vol% (4)
S01 10,2 2,62 0,143 11,0 4
S02 10,5 2,72 0,255 9,5 7
S03 10,4 2,90 0,468 3,5 12
S04 10,2 3,34 0,863 2,0 21
S05 10,3 3,11 1,379 4,5 30
S06 10,3 3,47 1,586 6,0 33
S07 10,2 3,24 2,195 1,5 42
S08 9,7 3,92 2,654 8,5 47
S09 10,4 4,46 3,519 12,5 55
S10 9,9 4,32 4,576 16,0 63
S11 10,2 4,63 4,874 11,0 65

(1) Determined by immersion method. (2) Measured with Kappabridge MFK1-FA Agico, property of IGEBA (UBA-CONICET), using a field of 200 A/m, corrected by self-demagnetization. (3) Obtained from AF demagnetization curves. (4) Estimated from magnetic susceptibility according toClark and Emerson relations (1991).

Source: Authors

Table 2: Origin of the analyzed samples

ID Origin
S01 Stockwork with phyllic alteration, Grasberg porphyry, Indonesia
S02 Lower andesite, Candelaria IOCG, Chile
S03 Banded Iron Formation (BIF), Eyre Peninsula, South Australia
S04
S05 Stockwork, Grasberg porphyry, Indonesia
S06 Skarn Ertsberg, Grasberg, Indonesia
S07 Banded Iron Formation (BIF), Eyre Peninsula, South Australia
S08 Magnetite breccia in lower andesite (magnetite-chalcopyrite), Candelaria IOCG, Chile
S09 Skarn Doz, Grasberg, Indonesia
S10 Lower andesite with chalcopyrite, Candelaria IOCG, Chile
S11 Lower andesite, Candelaria IOCG, Chile

Source: Authors

BIF (banded iron formation): chemically precipitated sedimentary rocks, most of them during the Archean, probably coinciding with the oxygenation of the oceans leading to massive precipitation of iron oxides. Most BIFs are highly metamorphosed. IOCG (iron oxide copper gold ore deposits): copper-gold ores within iron oxide dominant gangue. They are metasomatic rocks formed due to large alteration events driven by intrusive activity. Skarn: metasomatic rocks formed by the replacement of carbonate rocks caused by contact with an intrusive body. Stockwork: a system of veins developed in the core of porphyry copper-gold deposits in response to high-temperature hydrothermal alterations in calc-alkaline intrusions.

MBN measurement system

The diagram in Figure 1 shows the scheme of the measurement system. The tests were carried out using a magnetic yoke as an excitation source. This yoke was placed on each of the flat faces of the samples. The magnetic sensor coil was held between the magnetic yoke arms. The excitation magnetic field was achieved with a 10 Hz sinusoidal current produced by a Stanford function generator with a maximum voltage of 8 V, which was then amplified. The excitation and detection procedures were performed on the two circular faces of the cylindrical specimen, and then both results were averaged. Measurements were made with a four-channel digital oscilloscope (LeCroy Wave Runner 44MXi). Digitization was performed with a sampling frequency of 5 Ms/s, repeating each measurement five times on each face and considering their averages. In this way, the current on the yoke, the MBN signals, and the excitation voltage were recorded in three channels of the oscilloscope. Figure 2a shows the photograph of the measurement system. In Figure 2b, the magnetic probe (yoke and sensor coil) is positioned over a sample.

Scheme of the MBN measurement system

Figure 1: Scheme of the MBN measurement system

Source: Authors

Photograph of the measurement system, b) magnetic yoke and sensor coil positioned over the specimen

Figure2. a): Photograph of the measurement system, b) magnetic yoke and sensor coil positioned over the specimen

Source: Authors

To study the MBN signals, they were first digitally filtered in order to reduce the influence of noise. To this effect, a 4th-order Butterworth-type band pass filter in the range between 5 and 200 kHz was applied to the signals. Then, the RMS (root mean square) value of each filtered signal was calculated, and the corresponding averages were determined.

RESULTS AND DISCUSSION

Figure 3 shows the MBN signals (blue) for specimen S10 after they were filtered. They were obtained by exciting the yoke (red). From the filtered signals, the RMS value of the MBN was calculated for two complete cycles of excitation.

Excitation (red) and filtered MBN (blue) signals for sample S10

Figure 3: Excitation (red) and filtered MBN (blue) signals for sample S10

Source: Authors

In Figure 4, the average of the RMS values evaluated in both opposite flat faces of the samples was plotted as a function of the bulk magnetic susceptibility for all the specimens. As magnetic susceptibility depends on the amount of ferromagnetic minerals present in the sample, the slight increasing trend observed in the figure indicates that the greater the amount of magnetite, the more intense the RMS of the MBN measured. This is particularly true for samples with lower magnetite contents, since the magnetite surfaces in contact with the sensor are smaller. However, for samples with more than, say, 20 vol% magnetite, the effect of concentration becomes less significant, and the correlation worsens.

Graph of the RMS values as a function of the bulk magnetic susceptibility for all specimens (only the numbers in the rock IDs are shown)

Figure 4: Graph of the RMS values as a function of the bulk magnetic susceptibility for all specimens (only the numbers in the rock IDs are shown)

Source: Authors

In Figure 5, the RMS value is plotted for each test piece as a function of the median destructive magnetic field (shown in Table 1), which is considered to be indicative of the coercive force of the material. For multidomain materials, the coercive force increases with the presence of greater domain wall pinning and dislocations. Samples with lower magnetic susceptibility (S01 and S02) are clear outliers of any trend. For these samples, the very low values of the measured RMS are due to the low magnetite concentration, as previously discussed. For the rest of the samples, there is a linear relationship between the RMS value and the coercive force, with a positive correlation (R2=0,605). In particular, the BIF samples are the ones with the lowest RMS and coercive force, which is possibly due to recrystallization effect experienced by these samples (S03, S04, S07) during metamorphism, which leads to annealing with the consequent decrease in wall pinning. At the other extreme, magnetites of metasomatic origin (S06, S08, S09, S10, S11) have higher values of coercivity and RMS, possible evidence of the effect of impurities and/or stress.

Graph of the RMS values as a function of median destructive field of the natural remanent magnetization (only the numbers of the rocks are showed). Open symbols are used for outliers (samples with low RMS due to low magnetite concentration).

Figure 5: Graph of the RMS values as a function of median destructive field of the natural remanent magnetization (only the numbers of the rocks are showed). Open symbols are used for outliers (samples with low RMS due to low magnetite concentration).

Source: Authors

Other mechanisms could be studied to explain the fluctuation in the RMS value. This is an initial approach, and those relationships will be evaluated in future works.

CONCLUSION

This was the first time in Argentina that samples of rocks with different origins and varying proportions of magnetite were studied via the MBN technique.

The linear adjustment of the RMS values of the MBN with respect to the percentage of ferromagnetic minerals and magnetic susceptibility showed an increasing trend. A positive correlation was observed between the coercive force (estimated from the median destructive field) and the RMS of the MBN. The researchers interpret that the technique is sensitive to the abundance of magnetic material and that, for massive magnetite samples, it is sensitive to coercivity. In turn, this is conditioned by the geological history of the sample: metamorphosed rocks have lower RMS values, whereas rocks of metasomatic origin (particularly skarns and IOCG) have higher RMS values and coercive force.

REFERENCES

Butler, R. F. (1992). Paleomagnetism: From magnetic domains to geologic terranes. Blackwell Scientific Publications.

Chaparro, A. E., Gargiulo, J. D., Irurzun, M. A., Chaparro, M. A. E., Lecomte, K. L., Böhnel, H. N., Córdoba, F. E., Vignoni, P. A., Manograsso, C. N. T., Lirio, J. M., Nowaczyk, N. R., & Sinito, A. M. (2014). El uso de parámetros magnéticos en estudios paleolimnológicos en Antártida. Latin American Journal of Sedimentology and Basin Analysis, 21(2), 77-96. http://www.redalyc.org/articulo.oa?id=381741102002 [Link]

Clark, D. A., & Emerson, D. W. (1991). Notes on rock magnetization characteristics in applied geophysical studies. Exploration Geophysics, 22, 547-555. https://doi.org/10.1071/EG991547 [Link]

Dunlop, D. J., & Özdemir, Ö. (1997). Rock magnetism: Fundamentals and frontiers. Cambridge University Press. https://doi.org/10.1017/CBO9780511612794 [Link]

Ferrari, G. C., & Gómez, M. P. (2020). Caracterización de etapas de perforado en probetas multicapas mediante la emisión acústica generada durante la perforación. Tecnura, 24(63), 26-39. https://doi.org/10.14483/22487638.16193 [Link]

Filipussi, D. A., Muszkats, J. P., Sassano, M. P., Zitto, M. E., & Piotrkowski, R. (2019). Fractura de roca andesita y análisis espectral de señales de emisión acústica. Tecnura, 23(61), 45-56. https://doi.org/10.14483/22487638.15361 [Link]

Hoyos-Palacio, L. M., Espinel-Blanco, E., & Quintero-Martínez, Y. (2015). Caracterización fisicoquímica de cuarzo en el municipio de La Playa de Belén, departamento de Norte de Santander. Tecnura, 19(45), 41-52. https://doi.org/10.14483/udistrital.jour.tecnura.2015.3.a03 [Link]

Ivanchenko, V. S., Glukhikh I. I., Strokina, L. G., & Kheinson A. P. (2012). Magnetoacoustic emission of magnetites. Russian Geology and Geophysics, 53(2), 214-220. https://doi.org/10.1016/j.rgg.2011.12.018 [Link]

Jiles, D. (1991). Introduction to magnetism and magnetic materials. Chapman and Hall. https://doi.org/10.1007/978-1-4615-3868-4 [Link]

Neyra-Astudillo, M. R. (2017). Caracterización de materiales con técnicas de ruido magnético Barkhausen y emisión magneto acústica [Doctoral thesis, Universidad Nacional de General San Martín]. https://www.cnea.gob.ar/nuclea/handle/10665/1572 [Link]

Neyra-Astudillo, M. R., Núñez, N., López-Pumarega, M. I. Ruzzante, J., & Padovese-Rodríguez (2018). Ruido magnético Barkhausen para el estudio de la anisotropía magnética en aceros inoxidables. Revista Materia, 23(2), e12118. https://doi.org/10.1590/s1517-707620180002.0452 [Link]

Stacey, F. D., & Banerjee, S. K. (1974). The physical principles of rock magnetism. Elsevier.

Stefanita, C. G. (2008). From bulk to nano: The many sides of magnetism. Springer. https://doi.org/10.1007/978-3-540-70548-2 [Link]

Valencio, D. A. (1980). El magnetismo de las rocas: su aplicación geológica, la deriva continental, la tectónica de placas y otros problemas geofísicos y geológicos. EUDEBA.

Neyra-Astudillo., M.R. López-Pumarega., M.I. Evangelina-Geuna., S y Gómez., M. (2022). Magnetic Barkhausen Noise Measurements on Rocks. Tecnura, 26(73), 18-29. https://doi.org/10.14483/22487638.17148
This research, associated with the ICES (International Center of Earth Sciences) project, was endorsed and funded by the National Atomic Energy Commission.
Loading...