DOI:

https://doi.org/10.14483/udistrital.jour.RC.2017.29.a1

Publicado:

05/01/2017

Número:

Vol. 29 Núm. 2 (2017): Mayo-Agosto 2017

Sección:

Ciencia e ingeniería

CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors

Modelado CFD y cálculo de la transferencia de coeficiente de calor por convección de rotores de frenos de disco de automóviles

Autores/as

  • Ali Belhocine Mechanical Engineering, University of Sciences and the Technology of Oran, L.P 1505 El -MNAOUER, USTO 31000 ORAN ,Algeria),
  • Wan Zaidi Wan-Omar Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Malaysia

Palabras clave:

CFD, heat flux, convection, heat transfer coefficient, gray cast iron (en).

Palabras clave:

CFD, convection, gray cast iron, heat transfer coefficient, heat flux (es).

Biografía del autor/a

Ali Belhocine, Mechanical Engineering, University of Sciences and the Technology of Oran, L.P 1505 El -MNAOUER, USTO 31000 ORAN ,Algeria),

Mechanical Engineering, University of Sciences and the Technology of Oran, Algeria

Wan Zaidi Wan-Omar, Mechanical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Malaysia

Mechanical Engineering, Universiti Teknologi Malaysia, Skudai, Malaysia

Referencias

Belhocine, A., (2016), FE prediction of thermal performance and stresses in an automotive disc brake system. International Journal of Advanced Manufactoring Technology,Volume , Number , pp.1–16, Springer.

Belhocine, A. and Wan Omar, W.Z., (2016), Three-dimensional finite element modeling and analysis of the mechanical behavior of dry contact slipping between the disc and the brake pads, International Journal of Advanced Manufactoring Technology, Volume , Number , pp.1–17, Springer.

Cruceanu, C., (2007) ,Frâne pentru vehicle feroviare (Brakes for railway vehicles), Ed. MATRIXROM, Bucureşti, ISBN 978-973-755-200-6, 388 pag.

Dufrénoy, P., (2004), Two-/three-dimensional hybrid model of the thermomechanical behaviour of disc brakes‖, J Rail Rapid Transit Part F 218, pp 17–30.

Gotowicki, P.F., Vinzenco, N., Mariotti, G.V., (2005), Numerical and experimental analysis of a pegs- wing ventilated disk brake rotor with pads and cylinders, 10 th EAEC Eur.Automot. Cong – Paper EAEC05YUAS04– P 5.

Lee, S. and Yeo, T., (2000), Temperature and coning analysis of brake rotor using an axisymmetric finite element technique, Proc. 4th Korea-Russia Int. Symp. On Science & Technology, 3, 17-22.

Limpert, R., (1999),Brake Design and Safety, 2nd Edition, Warrendale,Pennsylvania: Society of Automotive Engineering Inc., pp. 137-144.

Ouyang, H., Abu Bakar, A.R., Li, L., (2009), A combined analysis of heat conduction, contact pressure and transient vibration of a disc brake, Intnational Journal of Vehicle Design, 51(1/2), 190-206.

Reimpel, J., (1998), Braking technology,Vogel Verlag, Würzburg.

Söderberg, A. and Andersson, S.,(2009) ,Simulation of wear and contact pressure distribution at the pad to-rotor interface in the disc brake using general purpose finite element analysis software, Wear 267,12(1), pp. 2243–2251.

Zhang, L., Yang, Q., Weichert, D., Tan, N., (2009), Simulation and Analysis of Thermal Fatigue Based on Imperfection Model of Brake Discs, Beijing Jiaotong University, PAMM • Proc. Appl. Math. Mech. 9, 533 – 534

Cómo citar

APA

Belhocine, A., y Wan-Omar, W. Z. (2017). CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors. Revista Científica, 29(2), 116–128. https://doi.org/10.14483/udistrital.jour.RC.2017.29.a1

ACM

[1]
Belhocine, A. y Wan-Omar, W.Z. 2017. CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors. Revista Científica. 29, 2 (may 2017), 116–128. DOI:https://doi.org/10.14483/udistrital.jour.RC.2017.29.a1.

ACS

(1)
Belhocine, A.; Wan-Omar, W. Z. CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors. Rev. Cient. 2017, 29, 116-128.

ABNT

BELHOCINE, Ali; WAN-OMAR, Wan Zaidi. CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors. Revista Científica, [S. l.], v. 29, n. 2, p. 116–128, 2017. DOI: 10.14483/udistrital.jour.RC.2017.29.a1. Disponível em: https://revistas.udistrital.edu.co/index.php/revcie/article/view/11602. Acesso em: 28 mar. 2024.

Chicago

Belhocine, Ali, y Wan Zaidi Wan-Omar. 2017. «CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors». Revista Científica 29 (2):116-28. https://doi.org/10.14483/udistrital.jour.RC.2017.29.a1.

Harvard

Belhocine, A. y Wan-Omar, W. Z. (2017) «CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors», Revista Científica, 29(2), pp. 116–128. doi: 10.14483/udistrital.jour.RC.2017.29.a1.

IEEE

[1]
A. Belhocine y W. Z. Wan-Omar, «CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors», Rev. Cient., vol. 29, n.º 2, pp. 116–128, may 2017.

MLA

Belhocine, Ali, y Wan Zaidi Wan-Omar. «CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors». Revista Científica, vol. 29, n.º 2, mayo de 2017, pp. 116-28, doi:10.14483/udistrital.jour.RC.2017.29.a1.

Turabian

Belhocine, Ali, y Wan Zaidi Wan-Omar. «CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors». Revista Científica 29, no. 2 (mayo 1, 2017): 116–128. Accedido marzo 28, 2024. https://revistas.udistrital.edu.co/index.php/revcie/article/view/11602.

Vancouver

1.
Belhocine A, Wan-Omar WZ. CFD Modeling and Computation of Convective Heat Coefficient Transfer of Automotive Disc Brake Rotors. Rev. Cient. [Internet]. 1 de mayo de 2017 [citado 28 de marzo de 2024];29(2):116-28. Disponible en: https://revistas.udistrital.edu.co/index.php/revcie/article/view/11602

Descargar cita

Visitas

861

Dimensions


PlumX


Descargas

Los datos de descargas todavía no están disponibles.

Recibido: de febrero de 2017; Aceptado: de abril de 2017

Abstract

Braking system is one of the basic organs to control a car. For many years, the disc brakes have been used in automobiles for safe retardation of the vehicles. During braking, enormous amount of heat will be generated, and for effective braking, sufficient heat dissipation is essential. The specific air flow surrounding the brake rotor depends on the thermal performance of the disc brake and hence, the aerodynamics is an important in the region of brake components. A CFD analysis is carried out on the braking system as the study of this case, to make out the behaviour of air flow distribution around the disc brake components using ANSYS CFX software. The main object of this work is to calculate the heat transfer coefficient (h) of the full and ventilated brake discs as a function of time using the CDF analysis which will be used later in the transient thermal analysis of the disc in ANSYS Workbench 11.0.

Keywords:

CFD, convection, gray cast iron, heat transfer coefficient, heat flux.

Resumen

El sistema de frenado es uno de los sistemas básicos para controlar un automóvil. Durante muchos años, los frenos de disco se han utilizado en los automóviles para el retraso seguro de los vehículos. Durante el frenado, se genera una enorme cantidad de calor, para un frenado eficaz, es esencial una disipación suficiente de calor. El flujo de aire específico que rodea al rotor del freno depende del rendimiento térmico del freno de disco y, por lo tanto, la aerodinámica es importante en la región de los componentes del freno. Se realizó un análisis CFD sobre el sistema de frenado como un estudio de este caso, para conocer el comportamiento de la distribución del flujo de aire alrededor del freno de disco utilizando el software ANSYS CFX. El objetivo principal de este trabajo es calcular el coeficiente de transferencia de calor (h) de los discos de freno completo y ventilado en función del tiempo utilizando el análisis CDF que se utilizará posteriormente en el análisis térmico transitorio del disco en ANSYS Workbench 11.0.

Palabras clave:

CFD, convección, Hierro fundido gris, Coeficiente de transferencia de calor, flujo de calor.

Resumo

O sistema de travagem é um dos órgãos básicos para controlar um carro. Durante muitos anos, os freios a disco têm sido usados em automóveis para garantir o atraso nos veículos. Durante a travagem, será gerada enorme quantidade de calor e, para uma travagem eficaz, é essencial uma dissipação de calor suficiente. O fluxo de ar específico sobre o rotor de freio depende do desempenho térmico do freio de disco e, portanto, a aerodinâmica é importante na região de componentes de freio. Uma análise CFD é realizada no sistema de travagem como o estudo deste caso, para determinar o comportamento da distribuição do fluxo de ar em torno dos componentes do freio de disco usando o software ANSYS CFX. O objetivo principal deste trabalho é calcular o coeficiente de transferência de calor (h) dos discos de freio completo e ventilado em função do tempo usando a análise de CDF que será usada mais tarde na análise térmica transitória do disco no ANSYS Workbench 11.0.

Palavras-chaves:

CFD, convecção, ferro fundido cinzento, coeficiente de transferência de calor, fluxo de calor.

Introduction

Today, the founding engineers of cars are currently in an unfailing position of maintaining and improving mechanical safety devices in the face of the increase in the need for highly efficient transport. The braking system is still the most careful safety device in automotive maintenance. Thus, the durability and performance of the brake discs also take into account the important aspect of the heating and the cooling of the latter during the braking phase. The impact is cooling factor of a brake disc by convection which must obviously be improved by thinning design modifications and contributes to the total heat flow for ordinary driving condition. Currently, the use of ventilated brake discs is an extraordinary process for improving the convective cooling of the brakes by means of the air passages separating the braking surfaces. Dufrénoy (2004) carried out, a thermomechanical analysis of the disc brake of real geometry taking into account the effect of wear and the variations of surface of contact. Söderberg & Andersson, (2009) conducted a study while developing a disc-brake pad model to calculate the contact pressure distribution at the pad interface and the rotor. The cone setting or thermal distortion of the disc results from the different distribution in the discs and brake pads according to the works of Lee and Yeo (2000). Ouyang et al. (2009) recently, they found that temperature is a factor that can affect the degree of vibration in a disc brake. Recently, Belhocine and Wan Omar (2016) have guided a static structural analysis of dry sliding contact between the brake disc and pads using the ANSYS 11.0 finite element software. After that, Belhocine (2016) conducted a coupled thermomechanical analysis showing the effect of temperature on the resulting stresses and overall deformations of the disc as well as; contact pressures in the brake pads.

The main aim of our work is to calculate the values of the convective heat transfer coefficient (h) using the ANSYS CFX 11.0 software, which must be expressed as a function of time for each surface of the full and ventilated disc and that they will be exploited to the determination of (3D) three-dimensional temperature of the disc under ANSYS Software in transient thermal regime (Zhang et al., 2009). Thus, the results induced by the analysis, show us the importance of ventilation in the brake discs design.

Brake disc kinds

In the automotive field, there are two kinds of brake discs; full discs and ventilated discs. Full discs generally include a crown attached to a "bowl", attached to the hub of the vehicle (figure1.a). Ventilated discs used in recent years are of complicated design and are installed on the front axles forming two crowns called flanges - separated by fins (figure 1.b). These vanes on ventilated discs provide better cooling and ventilation than full discs by elevating convective heat transfer surfaces. The design of ventilated discs is based on the constrictive material, the number, size and shape of the fins (radial fins, curves, circular pins, etc.) which are variable, thus ensuring better heat absorption capacity.

Types of discs: (a) Full disc (b) Ventilated disc.

Figure 1: Types of discs: (a) Full disc (b) Ventilated disc.

The gradients in the throat of the bowl are explained in the same way. At the beginning of braking, the temperature of the bowl is at 20 °C while that of the tracks is a few hundred degrees. In addition, in order to prevent the hub temperature from being too high, which would cause tire temperature increases, which is very critical of its behavior, the throat is machined so as not to transmit too much heat to the hub bowl (figure 2). With this machining, the temperature of the bowl actually decreases, but the thermal gradients increase consequently in this zone. These give rise to thermal stresses which explain the rupture of bowl observed during severe experimental tests.

Calorific throat in a ventilated disc.

Figure 2: Calorific throat in a ventilated disc.

A brake disc in rotational motion causes an air circulation in the channels, resulting in improved cooling (figure 3).

Circulation of air in the ventilated disc channels.

Figure 3: Circulation of air in the ventilated disc channels.

Governing equation of the transient heat conduction

In a 3-dimensional system, for an isotropic material within a domain Ω, for a volume element dxdydz, the difference between the incoming thermal flow and the outflow is defined as follows:

Where qx, qy and qz respectively represent the heat flux along the x, y and z axes per unit area.

Applying the thermal conservation law by equalizing the heat produced by the unit element Qdxdydz with the heat received due to the temperature change we obtain:

Where C, is the specific calorific capacity, ρ is the density and, T (x, y, z, t) is the temperature distribution.

According to, the Fourier law, the heat flux along the axes x, y and z are defined as:

After replacement in Equation (2), we obtain the following differential equation with the temperature variable T,

Finally, the three-dimensional thermal conduction equation in vector form is given as follows:

Convection processes

Convection is a heat transfer in a material medium with a movement of matter. This mode of transfer therefore concerns only fluids or exchanges between a solid and a fluid. This transfer mechanism is governed by Newton's law (figure 4):

Definition of an exchange surface element.

Figure 4: Definition of an exchange surface element.

with: φ is heat flow transmitted by convection (W), h is the coefficient of exchange by convection (Wm-2°C-1), Tp is surface temperature (°C), T∞ is temperature of the medium surrounding the surface (°C), and S is the area of contact surface, solid/fluid (m2).

Calculating heat fluxes entering the disc

The forces acting on the wheels during braking

By observing the situation described in figure 5, the longitudinal and transverse equilibrium of the vehicle can be written along the local axes x, y of the car.

Definition of the forces acting on an automobile during braking.

Figure 5: Definition of the forces acting on an automobile during braking.

with

For a road vehicle, the rolling force FRR=FG fr cos α is due to the flat formed by a tire on the road, fr is the rolling resistance coefficient. For a high pressure tire (fr=0.015)

The aerodynamic force is given by:

With CX coefficient of form, equal to: 0.3 to 0.4 on car

AF (m2) frontal surface; in the approach, for a road passenger vehicle, we can take:

AF= 0.8×height×width S

ρa air density

Total braking power

In the case of flat braking (figure 6), the resistances due to rolling and to the slope are neglected ( FRR=0 and FRP=0 ), the penetration into the air is generally negligible, for this reason, ( FRA=0 )

External forces acting on the vehicle during braking on a flat road.

Figure 6: External forces acting on the vehicle during braking on a flat road.

If we define, Let ϕ the factor of the ratio of the braking power with respect to the rear wheels PFH= ϕmav then, PFV= (1-ϕ)mav if a is constant, we have:

The braking power delivered to the brake disc is equal to half the total power:

At time t = 0, we have

The braking efficiency is then defined by the ratio between the deceleration (a) and the acceleration (g):

The purpose of the brake discs is to dissipate mechanical energy into heat. For trains or cars, during braking, the kinetic energy of the automobile must be lost and each surface of the disc receives an equal flux uniformly distributed between the diameters. The disc pad assembly heats up under this action and cools in the ambient air. As these brakes are repeated, the brake discs are subjected to thermomechanical fatigue. In the automotive industry, many studies have shown that braking can generate temperatures in excess of 700 °C in a matter of seconds.

Assuming that the amount of heat generated by friction is completely absorbed by the disc.

The expression of the transformed friction power per unit area is thus:

The quantity Q’v indicates the heat flow absorbed by the disc which must be housed only on the actual contact surface. Where Ad is the surface of the rotor to which a brake pad pivots. By definition, the operating factor εp of the friction surface is given by the following formula:

Thus, the equation of the initial thermal flow of friction entering the disc, which is calculated as follows:

Heat flux entering the disc

During efficient braking, the kinetic energy of a vehicle is therefore converted into thermal energy. During braking, each surface of the rotor receives a heat flux from the friction generated at the disc-pads interface. The expression of the initial heat flux entering the disc is given as follows (Reimpel, 1998):

Where a is the vehicle deceleration [ms-2], z=a/g is the braking effectiveness, and g is the gravity acceleration constant (9.81) [ms-2]. The brake disc actually absorbs more than 90% of the heat generated by friction (Cruceanu, 2007, p. 388). Given the difficulty of the problem treated, we will assume that the brake pads must be replaced by their friction effect and that they must be fictitiously represented by an incoming heat flux (figure 7).

Application of flux.

Figure 7: Application of flux.

In order to allow us to easily compare the results, the concrete dimensions of the two discs (full and ventilated) are quite similar. The main dimensions of the disc and the parameters involved are summarized in table 1 .

Table 1: Basic dimensions and main parameters of automotive braking.

We chose for the brake disc, gray cast iron material (FG 15) of carbon composition (Gotowicki et al., 2005), better thermomechanical specificities which are summarized in table 2.

Table 2: Disc material properties for thermal analysis.

Specific heat capacity and thermal conductivity of the material depend on the temperature are represented in figures 8 and 9.

Thermal conductivity as a function of temperature.

Figure 8: Thermal conductivity as a function of temperature.

Specific heat capacity as a function of temperature.

Figure 9: Specific heat capacity as a function of temperature.

CFD analysis with ansys CFX

Knowledge of the coefficient of exchange (h) in the flows is important and in the large backwater simulation, the turbulence model of k-ε of RNG is usually considered a desirable choice regarding rotation or swirling flow. Using ANSIS ICEM CFD, we have developed the presentation of the internal and external face differences used in the simulation for each full and ventilated disc while distinguishing them with distinct ones to facilitate our calculations as showed in figures 10 and 11. Mesh established in the disc is an irregular and non-uniform mesh, so that the meshes are more extended where there are weak gradients. The element of the mesh adopted in the calculation is tetrahedral linear with 30717 nodes and 179798 elements according to figure 12.

Full disc faces.

Figure 10: Full disc faces.

Ventilated disc faces.

Figure 11: Ventilated disc faces.

Wall meshes CFD simulation.

Figure 12: Wall meshes CFD simulation.

Fluid mesh generation

To allow us to develop the model corresponding to the domain of the fluid which is the air, we adopted a linear tetrahedral mesh with 30717 nodes and 179798 elements as illustrated in figure 13.

Meshing for a fluid body.

Figure 13: Meshing for a fluid body.

Using the ANSYS ICEM CFD software, and because of the symmetry of the brake disc, only a quarter of the fluid domain was taken into account in the calculations (figure 14).

Fluid body surfaces in ANSYS ICEM CFD.

Figure 14: Fluid body surfaces in ANSYS ICEM CFD.

The automatic model resolution (fluid-solid) allows us to draw at the end of simulation the values of the convective heat exchange coefficient (h) as a function of the time of the disc wall. The results obtained from the calculations for the two discs in the steady state are clearly shown on the figure 15.

Figure 15(b)-(c)-(d) show the distribution fields of the exchange coefficient (h) for the three types of materials. It is found that the behavior of (h) in the disc does not depend on the material chosen. The distribution of (h) in the disc is not the same as that existing in the literature.

Wall heat transfer coefficient distribution on a brake disc for various material at the steady state case.

Figure 15: Wall heat transfer coefficient distribution on a brake disc for various material at the steady state case.

Table 3: Value of the heat transfer coefficient of different surfaces in the stationary case for a full disc (FG 15).

Table 4 shows the mean values of the convective heat transfer coefficient (h) calculated by the minimum and maximum values of the various surfaces of the ventilated disc. It is found that the type of the material does not have a great influence on the variation of the convective heat transfer coefficient (h). Contrary to the first case, it is found that the value of the heat exchange coefficient (h) is strongly influenced by the ventilation system for the same material (FG 15).

Table 4: Value of the heat transfer coefficient of different surfaces in the stationary case for a ventilated disc (FG 25 AL, FG 20 and FG15).

Evaluation of the heat- exchange coefficient (h)

The convective heat exchange coefficient (h) or the coefficient of the film is a physical factor which is subordinate to the speed of the air flow and the geometry of the disc as well as other parameters related to the braking phenomena. This factor generally depends on the convection regime and the surface geometry but practically it has nothing to do with the material.

Figure 16 illustrates the evolution of the convective coefficient of exchange as a function of time for each face of the full and ventilated disc. These curves should be used in the following to evaluate the three-dimensional temperature of the two discs. It is observed that the geometric design of the full disc is varied towards a ventilated disc, the values of this coefficient also vary with this modification, it is quite reasonable because the ventilation leads to the reduction of the maximum temperatures of the walls. In figure17, the variation of the convective thermal coefficient of the wall as a function of time for the faces SV1 and SPV2 belonging respectively to the full and disc ventilated disc and for the same materialFG15.

CFD simulation results of convective heat exchange coefficient (h) for different l disc faces in transient mode of material (FG 15).

Figure 16: CFD simulation results of convective heat exchange coefficient (h) for different l disc faces in transient mode of material (FG 15).

Variation of the heat transfer coefficient (h) on the disc surface as a function of time for a material

Figure 17: Variation of the heat transfer coefficient (h) on the disc surface as a function of time for a material

Thermal loading applied to the disc

In this work, we have modeled the three-dimensional (3D) temperature of the brake disc for a stop braking of a medium-class vehicle, the speed of the latter reduces linearly with time until the braking time (t=3.5 s) and then stabilizes at zero until the end of the simulation (t=45 s), which is shown schematically in figure 18. The thermal loading imposed on the disc is expressed by a heat flux generated by friction and it follows the same behavior of the velocity and whose time variation is well shown in figure 19.

Braking power variation during simulation time.

Figure 18: Braking power variation during simulation time.

Heat flux variation during simulation

Figure 19: Heat flux variation during simulation

Mesh of disc brake model

The step of generating the mesh of the structure in the Workbench simulation is essential. For more accurate results in critical areas, we need to refine the mesh in the friction tracks of the brake disc where the brake pads pivot. Using the ANSYS software, we carried out a finite element mesh from the two discs shown in Figure 20; a full mesh disc in 172103 nodes and 114421 elements and a ventilated mesh disc of 154679 nodes and 94117 elements.

Reffined mesh on disc friction tracks: (a) Full disc, (b) Ventilated.

Figure 20: Reffined mesh on disc friction tracks: (a) Full disc, (b) Ventilated.

Boundary conditions applied to the model

We now simulate the brake disc in transient thermal regime under ANSYS Workbench software by introducing the involved materials properties and the boundary conditions. The total time of the simulation (t = 45 s) is the total braking time of the vehicle whose initial surface temperature of the disc is set at 20 °C (ambient temperature). In our simulation, we tested three types of gray cast iron (FG25AL, FG20 and FG 15) while exploiting the values of the heat transfer coefficient (h), those previously found in the form of curves (see figure 16) without forgetting to introduce the value of incoming stream obtained from the code ANSYS CFX.

Simulation results and discussions

Results of the disc temperature

On the figure. 21, we have shown for each type of material selected (FG 25 Al, FG 20, FG 15), the evolution of the temperature of the disc at the moment when it is reached. The disc material which has low thermal conductivity results in a temperature rise on the disc surface. It can be seen, that the material FG 15 has a maximum temperature (345.44°C) lower than those of the other materials FG 25 AL and FG 20 respectively, of temperatures 380.2 °C and 351.58 °C. From this figure, the material of Fonte Grise FG15 has a better thermal behavior. The full disc temperature reached its apogee value 401.55 °C at time t = 1.8839 s as indicated in figure 22, and then decreases exponentially to 4.9293 s on reaching the end of braking (t = 45 s). Figure 23 illustrates that the time difference [0-3.5 s] indicates the forced convection cycle. Free convection is carried out at the end of the latter until the simulation time limit (t = 45s). It is observed that the ventilated disc having a reduced temperature of almost 60 °C compared to a full disc. We conclude that ventilated brake discs in the vehicle design represent a good ventilation system and best means of cooling and them decrease temperatures better than full discs.

Results of thermal analysis of ventilated model for the three materials types FG 25 AL, (b) FG 20, (c) FG 15.

Figure 21: Results of thermal analysis of ventilated model for the three materials types FG 25 AL, (b) FG 20, (c) FG 15.

Contour of the two discs temperature distribution for material (FG15) (a) Full disc, (b) Ventilated disc.

Figure 22: Contour of the two discs temperature distribution for material (FG15) (a) Full disc, (b) Ventilated disc.

Evolution of disc temperature with braking time for material (FG 15)

Figure 23: Evolution of disc temperature with braking time for material (FG 15)

Conclusion

The present work presents a complex brake disc model to determine the values ​​of the heat exchange coefficient by convection (h) during the phase and braking conditions of the vehicle using the ANSYS CFX software. On the other hand, the numerical results of this investigation were exploited to solve the transient thermal scenario reacted in full and ventilated brake discs where their three-dimensional temperature was visualized using ANSYS Multiphysics 11.0 finite element software. The purpose of the contribution is to show the impact of ventilation in the cooling of discs in service which gives better thermal resistance by guaranteeing a better service life of these. As a conclusion, one could say that the numerical results of this simulation are quite adequate compared to what can be found in the literature. It is recommended that the same problem be solved on the experimental as an example through the test benches in order to validate the numerical model to match the current reality.

References

Belhocine, A. (2016). FE prediction of thermal performance and stresses in an automotive disc brake system. International Journal of Advanced Manufactoring Technology, 89(9), 1-16. Springer.

Belhocine, A. y Wan Omar, W.Z. (2016). Three-dimensional finite element modeling and analysis of the mechanical behavior of dry contact slipping between the disc and the brake pads. International Journal of Advanced Manufactoring Technology , 88(1), 1-17. Springer.

Cruceanu, C. (2007). Frâne pentru vehicle feroviare (Brakes for railway vehicles). Bucureşti: Ed. Matrixrom.

Dufrénoy, P. (2004). Two-/three-dimensional hybrid model of the thermomechanical behaviour of disc brakes. Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit, 218(1), 17-30.

Gotowicki, P.F., Vinzenco, N. y Mariotti, G.V. (2005). Numerical and experimental analysis of a pegs-wing ventilated disk brake rotor with pads and cylinders. Ponencia presentada en el X EAEC Eur.Automot. Cong. Paper EAEC05YUAS04, p 5.

Lee, S. y Yeo, T. (2000). Temperature and coning analysis of brake rotor using an axisymmetric finite element technique. Ponencia presentada en el IV Korea-Russia International Symposium on Science and Technology, 3, 17-22.

Ouyang, H., Abu Bakar, A.R. y Li, L. (2009). A combined analysis of heat conduction, contact pressure and transient vibration of a disc brake. Intnational Journal of Vehicle Design, 51(1/2), 190-206.

Reimpel, J. (1998). Braking technology. Vogel Verlag: Würzburg.

Söderberg, A. y Andersson, S. (2009). Simulation of wear and contact pressure distribution at the pad to-rotor interface in the disc brake using general purpose finite element analysis software. Wear 267, 12(1), 2243-2251.

Zhang, L., Yang, Q., Weichert, D. y Tan, N. (2009). Simulation and Analysis of Thermal Fatigue Based on Imperfection Model of Brake Discs. PAMM, 9(1), 533-534.

Belhocine, A. y Omar, W.Z.W. (2017). CFD modeling and computation of convective heat coefficient transfer of automotive disc brake rotors. Revista Científica, 29 (2), 116-128
Loading...